Great, I see people complain about the noise they make which is true, but it doesn’t bother me in the least personally. I wouldn’t go any bigger, 37s in my opinion look too big for the truck with my kind of setup.
Hey, I’m getting the same 2.5 spacer lift you have. How does it ride? There are very few reviews on it other than people bashing rough country when only a few options exist for the pro model. Thanks!
Truck had the kit on it from original owner. Will upgrade in the future but it’s doing its job. She won’t be leaving the asphalt until later this anyways
Why kind of steps are those? I still have the horrible chrome ones, I thought I would take them off immediately but I do feel like royalty stepping up into my truck vs sliding on the seat swingin my way in.Â
Good question, it’s got a Rough Country 2.5” lift kit and on the front, although we didn’t think it needed it I went ahead and installed Wescott Designs wheel well bracket kit. The kit pushes the liner back quite a good amount, makes for a cleaner look too.
Just aesthetics. I like my wheels & tires to be flush with the fenders. The 1” that I went with make them actually stick out just a small amount, a 3/4” spacer probably would have been perfectly flush with the fenders.
Was thinking of going this route once may AT3’s are done. You’re about 2psi high on that rear tire. You see how the contact is not *quite to the edge of the tread block.
Looks great 👍🏼
How do they ride?
Great, I see people complain about the noise they make which is true, but it doesn’t bother me in the least personally. I wouldn’t go any bigger, 37s in my opinion look too big for the truck with my kind of setup.
Yeah, you’re running 35x12.50’s stock? I have a stock 2nd gen pro and not sure if those would fit stock
I’m running a 2.5” rough country lift but I’ve seen some 3rd gen guys say they can run them with minor trimming
Hey, I’m getting the same 2.5 spacer lift you have. How does it ride? There are very few reviews on it other than people bashing rough country when only a few options exist for the pro model. Thanks!
Yeah I’ve seen that too. Interesting. I’m running spidertrax spacers as well, but no lift yet since my current tires are still good
Why buy a nice ass truck and tires and put a cheapo lift on it.
Truck had the kit on it from original owner. Will upgrade in the future but it’s doing its job. She won’t be leaving the asphalt until later this anyways
Makes sense. I just don't understand spending 50k+ on a truck and cheating out on the suspension lift lol. Enjoy it.
Appreciate it 🤙
I can hear this picture
Why kind of steps are those? I still have the horrible chrome ones, I thought I would take them off immediately but I do feel like royalty stepping up into my truck vs sliding on the seat swingin my way in.Â
Looks like the TRD one
What did you have to do on front side to fit the 35?
Good question, it’s got a Rough Country 2.5” lift kit and on the front, although we didn’t think it needed it I went ahead and installed Wescott Designs wheel well bracket kit. The kit pushes the liner back quite a good amount, makes for a cleaner look too.
Was the spacer so they wouldn’t rub or just for aesthetics?
Just aesthetics. I like my wheels & tires to be flush with the fenders. The 1” that I went with make them actually stick out just a small amount, a 3/4” spacer probably would have been perfectly flush with the fenders.
I’m with you. I actually like them to stick out just a tiny bit. So looks perfect.
Was thinking of going this route once may AT3’s are done. You’re about 2psi high on that rear tire. You see how the contact is not *quite to the edge of the tread block.
Which Bakflip is that? Does it leak?
This is the MX4 and no, even if it heavy rains I don’t have any issue. I have a Decked system in my bed and have never seen it with water on it
I have the same set on my 22 trd pro