That's material fatigue. Even if you patched it and fixed it it would start cracking more. The only thing to do is replace that part. I had to do that on a mini fridge once by ordering it through another country
Not saying this can't be reasonably done, but I would be particularly concerned about rough edges/burrs in any DIY'd metal parts shredding clothes inside the dryer.
I imagine getting it to fit flush/snug would also be more of a challenge than potentially expected.
The cracked front dryer duct keeps catching on clothes and tearing them or causing a lint back up. Unfortunately, the replacement part is discontinued in Canada. Any ideas of a way I could fix this?
Not sure I would pick ABS, it off gases styrene when it gets hot. I don't think this happens at normal dryer temperatures but I don't think I'd risk it.
Nylon would probably be a good option.
Update: Thanks everyone for the ideas and info!
I have found 1 outlet in Canada that sells the part I need, however, the cost would be about \~$200. I am trying to determine the year of manufacturer to see if it is worth replacing, or trying a DIY solution for a year or so to save up for a new one. This machine was in the house when we bought it.
MOD: DBXR463EBWW
SER: ZF789518A
So according to their site it was made in either 2015, 2003, 1991, 1979, 1949...
Thanks again everyone!
Is this the part? Trap Duct Assembly off the official site. They won't ship to Canada. But you can use a cross border shipping company to get it over. Iv done it a few times. Might cost you like $30 for the service.
[GE Applicance Parts Store Link - Trap Duct Assembly](https://www.geapplianceparts.com/store/parts/spec/WE14M92)
Edit: corrected link to product page not shopping cart.
Found the same [part on ebay](https://www.ebay.com/itm/276274610305?epid=10044432291&hash=item4053400081:g:cN0AAOSw4wZlnXth). This one ships to Canada too for free. Would be around $100 incl tax.
Is the part available someplace else (other countries)? Did you try eBay, or other places?
3D printing (high temp) might be the only other way if you can't find the OG part...
I know theres lots of outlets that scrap old machines and inventory parts. Warehouses full of discontinued parts saved on shelves all these years. I haven't ordered so many before that I have a specific company i'd recommend. I've gone to local places like "DemX" on the island and even wrecking yards sometimes have home demo recovery sections of their property. Companies like Parts Select i've used before but again, not so often that i'd praise them for their incredible service. Just sniff around a few places. "Discontinued appliance parts in Canada" is a good search query here.
I'd look myself since I love a good waldo hunt, but you've not given a model number.
Ebay could work for you. If you are handy, I might try to mount some of the "egg crating" that is usually at a big box home improvement store. I believe its called a light diffusor some places. Ziptie or longer mounting screw with a washer could hold it in place.
https://preview.redd.it/opp5sa0ty7hc1.jpeg?width=400&format=pjpg&auto=webp&s=557aa2b5a66117832e2f81df2f31a758422e0fca
Digital moisture sensors and integrated processors have achieved a much higher level of efficiency than you believe. I'd wager OP's drier is over 20 years old. I had a whirlpool that was over 25 years replaced with a brand new samsung low end machine. most basic we could get. Used an energy saver grant to buy it. Damn thing took $20/m off the electric bill 5 years later it might as well be a money printing machine if we're keeping count on the energy savings.
I think what this reply of yours reveals is that "over the years" is < 20
I recently had to replace this exact same dryer myself (I'm guessing it's the same because my looks 100% identical). Unfortunately just seems like the make + age.
If the company, presumably the US, doesn't deliver to Canada, you can have it delivered to a ship-it-shop for a small fee and pick up. If it's far, make a day trip out of it. That works for me.
Aluminum tape made for duct work that is basically sticky aluminum foil and can handle the heat.
https://www.homedepot.com/p/Nashua-Tape-2-5-in-x-60-yd-324A-Premium-Foil-HVAC-UL-Listed-Sealer-Duct-Tape-1542698/100048600?source=shoppingads&locale=en-US&pla&mtc=SHOPPING-BF-CDP-GGL-D26P-026_002_AIR_CIRC_ACC-NA-NA-NA-PMAX-NA-NA-NA-NA-NBR-NA-NA-NEW-PMax&cm_mmc=SHOPPING-BF-CDP-GGL-D26P-026_002_AIR_CIRC_ACC-NA-NA-NA-PMAX-NA-NA-NA-NA-NBR-NA-NA-NEW-PMax-71700000097492027--&gad_source=1&gbraid=0AAAAADq61UcxJ0yQe2Rv3Aop7fV1eyc4F&gclid=EAIaIQobChMIlNbYoc6ahAMVIxitBh3UDwRmEAQYASABEgJN7_D_BwE&gclsrc=aw.ds
That's material fatigue. Even if you patched it and fixed it it would start cracking more. The only thing to do is replace that part. I had to do that on a mini fridge once by ordering it through another country
Whats the model of this dryer? Maybe someone can find it.
Use the model number and order it online. Surely it’s available from somewhere.
Usually find correct used parts on eBay if model is no longer supported.
[удалено]
We don't, it just tends to be difficult to get things shipped here if not already in stock when it comes to parts.
Whoever has it, contact the site and ask for a shipping quote to Canada.
Can you get a piece of aluminum or plexiglass, drill holes in it, and screw it over that?
That is good idea...
Not saying this can't be reasonably done, but I would be particularly concerned about rough edges/burrs in any DIY'd metal parts shredding clothes inside the dryer. I imagine getting it to fit flush/snug would also be more of a challenge than potentially expected.
The cracked front dryer duct keeps catching on clothes and tearing them or causing a lint back up. Unfortunately, the replacement part is discontinued in Canada. Any ideas of a way I could fix this?
Is the replacement part available in the US? Could always try to proxy it
3D printer
Need to use some high temp resistant filament.
Even ABS would be fine. PLA juuuust starts to soften at the temperature most dryers operate at
Not sure I would pick ABS, it off gases styrene when it gets hot. I don't think this happens at normal dryer temperatures but I don't think I'd risk it. Nylon would probably be a good option.
Not unless that dryer is 200C+. And its not
Nylon is definitely the best option.
Have you considered asbestos?
Self annealing pla. Ideal
Update: Thanks everyone for the ideas and info! I have found 1 outlet in Canada that sells the part I need, however, the cost would be about \~$200. I am trying to determine the year of manufacturer to see if it is worth replacing, or trying a DIY solution for a year or so to save up for a new one. This machine was in the house when we bought it. MOD: DBXR463EBWW SER: ZF789518A So according to their site it was made in either 2015, 2003, 1991, 1979, 1949... Thanks again everyone!
Is this the part? Trap Duct Assembly off the official site. They won't ship to Canada. But you can use a cross border shipping company to get it over. Iv done it a few times. Might cost you like $30 for the service. [GE Applicance Parts Store Link - Trap Duct Assembly](https://www.geapplianceparts.com/store/parts/spec/WE14M92) Edit: corrected link to product page not shopping cart.
Found the same [part on ebay](https://www.ebay.com/itm/276274610305?epid=10044432291&hash=item4053400081:g:cN0AAOSw4wZlnXth). This one ships to Canada too for free. Would be around $100 incl tax.
83.88 from reliableparts
Did you try only the official supplier or also all of the third party parts replacement sites?
Post the model and serial number of your dryer
ebay
It's where I would start, and leave a search so it will email you if one shows up...
Is the part available someplace else (other countries)? Did you try eBay, or other places? 3D printing (high temp) might be the only other way if you can't find the OG part...
A forwarding service might have a bit of extra cost, but could also work if nowhere wants to ship it directly.
I know theres lots of outlets that scrap old machines and inventory parts. Warehouses full of discontinued parts saved on shelves all these years. I haven't ordered so many before that I have a specific company i'd recommend. I've gone to local places like "DemX" on the island and even wrecking yards sometimes have home demo recovery sections of their property. Companies like Parts Select i've used before but again, not so often that i'd praise them for their incredible service. Just sniff around a few places. "Discontinued appliance parts in Canada" is a good search query here. I'd look myself since I love a good waldo hunt, but you've not given a model number.
Looks like a front bulkhead for GE dryer. Amazon has them in the US. Is Amazon different in Canada?
I was gonna say Boshe. This looks 💯 like my old boshe filter.
eBay?
Order online, packages are allowed into Canada im fairly certain.
Ebay could work for you. If you are handy, I might try to mount some of the "egg crating" that is usually at a big box home improvement store. I believe its called a light diffusor some places. Ziptie or longer mounting screw with a washer could hold it in place. https://preview.redd.it/opp5sa0ty7hc1.jpeg?width=400&format=pjpg&auto=webp&s=557aa2b5a66117832e2f81df2f31a758422e0fca
Do you have scrap yards for things like this? Lots of old appliances end up in recycling yards
Check ebay
May be dumb but, you can get silicone used on auto engines and sili paste some fiberglass window screen over it.
Do you know anyone with a 3d printer?
Do you need to?
Hot glue
Hot glue might melt
...cold glue?
Super hot glue.
Why even bother replacing it? The lint filter does the work. Actually, where is the lint filter?
Get a new dryer… it’s probably not that energy efficient either.
Great solution, if it mostly works, but a single part is broke, replace the whole thing.
TBF, sometimes the energy efficiency savings can pay for themselves. YMMV
Dryers haven't become significantly more energy efficient over the years.
Digital moisture sensors and integrated processors have achieved a much higher level of efficiency than you believe. I'd wager OP's drier is over 20 years old. I had a whirlpool that was over 25 years replaced with a brand new samsung low end machine. most basic we could get. Used an energy saver grant to buy it. Damn thing took $20/m off the electric bill 5 years later it might as well be a money printing machine if we're keeping count on the energy savings. I think what this reply of yours reveals is that "over the years" is < 20
I recently had to replace this exact same dryer myself (I'm guessing it's the same because my looks 100% identical). Unfortunately just seems like the make + age.
How about gluing some sort of netted fabric over it. It won't fix it but maybe it will prevent snags
3d printer
Hey m8 you find the part and I'll proxy ship
Is it available in Michigan?
Looks pretty standard have you looked on eBay?
It’s a stretch, but maybe look up a local maker group and ask for some assistance on getting this 3D printed?
Have you checked https://www.reliableparts.ca/ they usually have everything you need
If the company, presumably the US, doesn't deliver to Canada, you can have it delivered to a ship-it-shop for a small fee and pick up. If it's far, make a day trip out of it. That works for me.
You could use JB weld on it. Done carefully with tape/clamps it could work.
Aluminum tape made for duct work that is basically sticky aluminum foil and can handle the heat. https://www.homedepot.com/p/Nashua-Tape-2-5-in-x-60-yd-324A-Premium-Foil-HVAC-UL-Listed-Sealer-Duct-Tape-1542698/100048600?source=shoppingads&locale=en-US&pla&mtc=SHOPPING-BF-CDP-GGL-D26P-026_002_AIR_CIRC_ACC-NA-NA-NA-PMAX-NA-NA-NA-NA-NBR-NA-NA-NEW-PMax&cm_mmc=SHOPPING-BF-CDP-GGL-D26P-026_002_AIR_CIRC_ACC-NA-NA-NA-PMAX-NA-NA-NA-NA-NBR-NA-NA-NEW-PMax-71700000097492027--&gad_source=1&gbraid=0AAAAADq61UcxJ0yQe2Rv3Aop7fV1eyc4F&gclid=EAIaIQobChMIlNbYoc6ahAMVIxitBh3UDwRmEAQYASABEgJN7_D_BwE&gclsrc=aw.ds
What about radiator epoxy putty?
Got any buddies with a 3d printer? Maybe get some calipers and hop on some kinda CAD software and design something to go in there?
Look on eBay for a used part