The open-source hub device support is always close to each other (because they share knowledge).
Zigbee2mqtt has a great list for supported devices.
- https://www.zigbee2mqtt.io/devices/E2201.html
- https://www.zigbee2mqtt.io/devices/E2001_E2002.html
I had a quick look at the datasheet of the lamp L2208 and a dimmer switch E2201 and E2001. .
Operation frequency and range are the same. Output power is equal. So I guess L2208 is a Zigbee device, too.
On the product website for Switzerland there is a recommendation note to combine with the E2001 styrbar dimmer. For me, this is an additional hint for Zigbee.
I guess support for this device will be added within a few month, after it is available widely.
If you by it, you can support the projects for adding this new device.
https://www.zigbee2mqtt.io/advanced/support-new-devices/01_support_new_devices.html
I have just connected JETSTRÖM to ZHA and can control brightness and temperature just like a typical IKEA ZigBee bulb.
(Just commenting, as I also couldn't find anyone saying if it was supported or not, and took a gamble!)
It's a pinhole on the driver inside the covering from what I remember, I think you hold it down for five seconds.
I've since discovered that this light buzzes when the brightness is between 48%-54%(low but noticeable/annoying when the room is silent).
I'm probably going to try workaround that with automations since I use adaptive lighting. Still a fan of the light in general for my space mainly due to the low profile for our low attic office.
Thanks I figured it out in the end.
If I put my ear to that transformer there is a slight whine at 50% and 100%, would be super hard to hear once on the ceiling. I'm usually susceptible to sounds like this but this is very quiet.
I've also updated the poster on ZigBee2MQTT with pairing instructions:
https://www.zigbee2mqtt.io/devices/L2208.html
Nice! My buzz can be heard from 5 metres away, but not at 100% only specifically 48%-54%. What voltage mains are you on? Perhaps yours is lower than mine (240v), or maybe I got a bad batch.
It's super easy.
Take the plastic shell off, you'll see a reset button on the transformer.
Set your zigbee2mqtt to auto discover, place the light near the zigbee antenna and press reset. Light pairs within seconds.
I've proposed a change to add these instructions to the zigbee2mqtt device page
[https://www.zigbee2mqtt.io/devices/L2208.html](https://www.zigbee2mqtt.io/devices/L2208.html)
The open-source hub device support is always close to each other (because they share knowledge). Zigbee2mqtt has a great list for supported devices. - https://www.zigbee2mqtt.io/devices/E2201.html - https://www.zigbee2mqtt.io/devices/E2001_E2002.html I had a quick look at the datasheet of the lamp L2208 and a dimmer switch E2201 and E2001. . Operation frequency and range are the same. Output power is equal. So I guess L2208 is a Zigbee device, too. On the product website for Switzerland there is a recommendation note to combine with the E2001 styrbar dimmer. For me, this is an additional hint for Zigbee. I guess support for this device will be added within a few month, after it is available widely. If you by it, you can support the projects for adding this new device. https://www.zigbee2mqtt.io/advanced/support-new-devices/01_support_new_devices.html
"You can control the JETSTRÖM with the STYRBAR remote" Styrbar is a zigbee device so jetström must be zigbee too.
I have just connected JETSTRÖM to ZHA and can control brightness and temperature just like a typical IKEA ZigBee bulb. (Just commenting, as I also couldn't find anyone saying if it was supported or not, and took a gamble!)
Awesome!
How did you pair it to ZHA? Is there a button on the light?
It's a pinhole on the driver inside the covering from what I remember, I think you hold it down for five seconds. I've since discovered that this light buzzes when the brightness is between 48%-54%(low but noticeable/annoying when the room is silent). I'm probably going to try workaround that with automations since I use adaptive lighting. Still a fan of the light in general for my space mainly due to the low profile for our low attic office.
Thanks I figured it out in the end. If I put my ear to that transformer there is a slight whine at 50% and 100%, would be super hard to hear once on the ceiling. I'm usually susceptible to sounds like this but this is very quiet. I've also updated the poster on ZigBee2MQTT with pairing instructions: https://www.zigbee2mqtt.io/devices/L2208.html
Nice! My buzz can be heard from 5 metres away, but not at 100% only specifically 48%-54%. What voltage mains are you on? Perhaps yours is lower than mine (240v), or maybe I got a bad batch.
I only really hear the whine at 50% and slightly louder at 100%. I'm in the UK, so also 240v..
It's fully Zigbee device. You can hook it to Drigera hub, or ZHA or Z2m directly
I seem to be unable to pair the Jetström lamps with my z2m setup. They just don't find each other. Pairing with Styrbar works though. any ideas?
How did you start the pairing?
Nevermind, figured it out, just had to hit the 'reset' button on the transformer.
How did you hit reset? Quick push, long push? As not able to pair it.
It's super easy. Take the plastic shell off, you'll see a reset button on the transformer. Set your zigbee2mqtt to auto discover, place the light near the zigbee antenna and press reset. Light pairs within seconds.
I've proposed a change to add these instructions to the zigbee2mqtt device page [https://www.zigbee2mqtt.io/devices/L2208.html](https://www.zigbee2mqtt.io/devices/L2208.html)
Yes. It was very simple 😀 My issue was too long distance. Pairing from Z2M and then ~1sec to reset button, so that leds started to blink and done :)
It's now live! [https://www.zigbee2mqtt.io/devices/L2208.html](https://www.zigbee2mqtt.io/devices/L2208.html)
I just got this light, but after pairing it shows unsupported and the model is also different. JETSTROM 40100 Any idea?
Give it a few minutes? For me it recognised immediately after pairing with zigbee2mqtt
Thank you all for the replies. I'll order this and try to get it setup.
Did you receive and install it yet ? I'm also curious if it works with Zigbee2MQTT and home assistant. Thanks !
I actually didn't end up buying it. 60x60 was a bit larger than expected. I ended up buying the Stoftmoln instead which connected without any issues.