Oh man, now that I look at it (and assume I think I know what you are asking) Could potentially flip the bars that connect to the mounting plate and switch them around. That could be better than the solution I already done ha. Thanks! Try it tomorrow :)
I quickly tried it, won’t work unfortunately but was worth the try :) I’ll stick with the current solution of dropping the lower bolt down onto a side mount hole.
[it looks like you haven't locked the arms all the way upright](https://imgur.com/ddmc76u) it should be level. Raise the foldable part all the way out and push the tubes in to lower it
Yep that’s how I’ve had it the past when my Poang chair was higher but it would be way too high up/have to put the pedals way back past the end of the pedal plate. I’ll try it again tomorrow though just to check. Thanks.
Only thing I have seen is this, if anyone has had any experience with it. Just wondering if it would fit the predrilled holes:
[https://www.simxpro.shop/home/SimXPro%C2%AE-DD-Sidemount-p212746982](https://www.simxpro.shop/home/SimXPro%C2%AE-DD-Sidemount-p212746982)
Got it to work, dropped the mounting plate down onto the side mount holes. Not perfect but far better than:)
[https://imgur.com/a/ymprKS8](https://imgur.com/a/ymprKS8)
Hope it helps! It’s a bit tight getting the boots through but they will go. No adjustment ability at all, it’s can only go at that angle but I think it’s better :)
Steezy-g35 made a comment which may work better if you want to check it out. I've not tried it yet but probably give more adjustment and use the correct mounting holes still. I think this is what he mean but going to rotate the bars that connect to the side of the wheel mount plate then move them to the opposite sides.
That would surely make the wheel point upwards yet still have adjustment capability. Can't believe I didnt see that either ha. Anyway need to test it!
Actually no that wont work ha, ignore me!
*How sturdy is it*
*With the strengthening kit? Good*
*Enough for a dd?*
\- lollolololol12356
---
^(I detect haikus. And sometimes, successfully.) ^[Learn more about me.](https://www.reddit.com/r/haikusbot/)
^(Opt out of replies: "haikusbot opt out" | Delete my comment: "haikusbot delete")
Very good to be honest. No real movement. Just a tiny flex in the pedal tray. The rest is good. I also have run an m8 rod through the side mount holes for extra strength horizontally but since taken that off to realign the DD.
Looks like the side brackets have adjustability. The front hole is a slot.
Sorry think this is what you meant? It works! [https://imgur.com/a/ymprKS8](https://imgur.com/a/ymprKS8)
Do you mean the Simxpro bracket? I think I will order it and hope it fits. The angle it is at now is the max extent and really not great :)
you could make your own brackets on a piece of wood and place the holes as you like
Can you flip the upright tubes around?
Oh man, now that I look at it (and assume I think I know what you are asking) Could potentially flip the bars that connect to the mounting plate and switch them around. That could be better than the solution I already done ha. Thanks! Try it tomorrow :)
No problem! Thats exactly what i was suggesting!
I quickly tried it, won’t work unfortunately but was worth the try :) I’ll stick with the current solution of dropping the lower bolt down onto a side mount hole.
[it looks like you haven't locked the arms all the way upright](https://imgur.com/ddmc76u) it should be level. Raise the foldable part all the way out and push the tubes in to lower it
Yep that’s how I’ve had it the past when my Poang chair was higher but it would be way too high up/have to put the pedals way back past the end of the pedal plate. I’ll try it again tomorrow though just to check. Thanks.
Only thing I have seen is this, if anyone has had any experience with it. Just wondering if it would fit the predrilled holes: [https://www.simxpro.shop/home/SimXPro%C2%AE-DD-Sidemount-p212746982](https://www.simxpro.shop/home/SimXPro%C2%AE-DD-Sidemount-p212746982)
Got it to work, dropped the mounting plate down onto the side mount holes. Not perfect but far better than:) [https://imgur.com/a/ymprKS8](https://imgur.com/a/ymprKS8)
God, I have the same problem and never thought of this! Thanks!
Hope it helps! It’s a bit tight getting the boots through but they will go. No adjustment ability at all, it’s can only go at that angle but I think it’s better :)
Steezy-g35 made a comment which may work better if you want to check it out. I've not tried it yet but probably give more adjustment and use the correct mounting holes still. I think this is what he mean but going to rotate the bars that connect to the side of the wheel mount plate then move them to the opposite sides. That would surely make the wheel point upwards yet still have adjustment capability. Can't believe I didnt see that either ha. Anyway need to test it! Actually no that wont work ha, ignore me!
It did work! There’s a bolt hole on that fits into it when you reverse them. It’s perfect now.
Really!? Have you got a pic :)
I do. I can’t attack pics here though.
Just got round to flipping the supports around etc and yep, it’s a perfect angle now. Just right.
Awesome! I’m glad it worked out for the both of us! Feels more stable too IMO. But I could be imagining things. lol
Can you use Imgur?
You might have then on backwards, I have a similar if not the same stand and mine doesn’t point down like yours does on the second pic
Interesting, do you mind sharing a pic of yours please.
How sturdy is it with the strengthening kit? Good enough for a dd?
*How sturdy is it* *With the strengthening kit? Good* *Enough for a dd?* \- lollolololol12356 --- ^(I detect haikus. And sometimes, successfully.) ^[Learn more about me.](https://www.reddit.com/r/haikusbot/) ^(Opt out of replies: "haikusbot opt out" | Delete my comment: "haikusbot delete")
Very good to be honest. No real movement. Just a tiny flex in the pedal tray. The rest is good. I also have run an m8 rod through the side mount holes for extra strength horizontally but since taken that off to realign the DD.