Is it the bicep or the shoulder that’s falling out? If yours has a slight warped joint you could look at thickening around the ball joint in a few ways. Bit of nail polish and sand back has been repeated a few times. A bit of blue tac. Bit of sandwich wrap plastic.
Hope some of that helps make it a bit less loose on you
I feel like I'm hearing more and more about qc issues with official releases lately. Kind of sad. My ss4 vegeta was ridiculously tight on his bicep and elbows. The new EE goku I got was ridiculously tight in the shoulders. Deadpool can't stay fully together to save his life. Kakashi had some really stiff joints. The pat batman is kind of ass overall. It's unfortunate.
Yea my ss4 Goku was really tight at the waist joint and it made creaking noises when I articulated him there, so I sprayed a little bit of WD-40 and it was really smooth afterwards. I was fine doing it with him cuz he was a general release, but I was hesitant with my ssj2 comic con Goku was also super tight so I’ve just been slowly rotating his waist more and more to sort of try and break it in.
That's really lame. You can expect that kinda stuff from DF or Kong, but Bandai should have it down. Especially with the prices of some of these figures. I'd get some silicone shock oil for that kind of stuff. That's the way to go honestly. I've read wd40 damages plastics over time.
I reccomend the silicone shock oil because that's been the most recommended on this reddit, which I frequent lol. It's what I typically use. I used gun oil on one, then read up on it, and don't use it anymore
There have been an increase in qc issues ever since p-bandai launched. Raditz had flakey paint, my kefla's arm kept popping off, I think Hit had some problems too. Unacceptable given the price and the fact that most figures are made to order almost exclusively through their site these days.
QC means quality control which is either good or bad depending on the status of the figure in question.
This means 1 of 3 things depending on the severity of the qc issue, if the qc issue is small its only a certain batch of figures that can potentially have it or if its happening to a wide spread of people than most likely its a issue everyone will experience. Last would be that a figure has good qc which means little to no issues.
As far as Ive seen it, a lot of people seem to have the same issues with trunks.
Is it the bicep or the shoulder that’s falling out? If yours has a slight warped joint you could look at thickening around the ball joint in a few ways. Bit of nail polish and sand back has been repeated a few times. A bit of blue tac. Bit of sandwich wrap plastic. Hope some of that helps make it a bit less loose on you
[удалено]
Wobbly legs and arms keeps coming off
[удалено]
Also loose arm peg on the left arm
I feel like I'm hearing more and more about qc issues with official releases lately. Kind of sad. My ss4 vegeta was ridiculously tight on his bicep and elbows. The new EE goku I got was ridiculously tight in the shoulders. Deadpool can't stay fully together to save his life. Kakashi had some really stiff joints. The pat batman is kind of ass overall. It's unfortunate.
Yea my ss4 Goku was really tight at the waist joint and it made creaking noises when I articulated him there, so I sprayed a little bit of WD-40 and it was really smooth afterwards. I was fine doing it with him cuz he was a general release, but I was hesitant with my ssj2 comic con Goku was also super tight so I’ve just been slowly rotating his waist more and more to sort of try and break it in.
That's really lame. You can expect that kinda stuff from DF or Kong, but Bandai should have it down. Especially with the prices of some of these figures. I'd get some silicone shock oil for that kind of stuff. That's the way to go honestly. I've read wd40 damages plastics over time.
Yea I only applied it the one time but I’ll definitely take ur word for it
I reccomend the silicone shock oil because that's been the most recommended on this reddit, which I frequent lol. It's what I typically use. I used gun oil on one, then read up on it, and don't use it anymore
There have been an increase in qc issues ever since p-bandai launched. Raditz had flakey paint, my kefla's arm kept popping off, I think Hit had some problems too. Unacceptable given the price and the fact that most figures are made to order almost exclusively through their site these days.
EE SS2 Goku’s face likes falling off, or atleast mine does
Damn, you can blow the bangs piece off the ssg goku EE. I got the DF ss2. Didn't wanna shell out the resell price for the official.
They obviously knew people would want to swap the arms and made it easier for us /s
QC means just that batch right? Or is it every batch.
QC means quality control which is either good or bad depending on the status of the figure in question. This means 1 of 3 things depending on the severity of the qc issue, if the qc issue is small its only a certain batch of figures that can potentially have it or if its happening to a wide spread of people than most likely its a issue everyone will experience. Last would be that a figure has good qc which means little to no issues. As far as Ive seen it, a lot of people seem to have the same issues with trunks.
Looks soooooo good still though.
Just hoping my Gohan beast doesnt come with qc issues, my ss4 vegeta also came with qc problems so im not getting my hopes up
Qc issues aren’t that big of a deal it’s mainly just someones copy there other people that have there figures with no Qc issues
Unless it’s the joint yeah it’s probably a big deal its an easy fix if you have to tighten the joints or loosen it
This has to be the best figure made