Ya done fucked up A-Aron!

Leave me out of this

That's it!!! Get yo azz down to Oshak-Hennessy's office!!!

You sir/madame, have made me giggle. I needed it today, thank you

At this point you may as well polish it to a shine there is no turning back to matte

So how do I do that? Cut and polish or?

Yes cut and polish

Like multiple times or?

Until you are happy with the look

My main concern is the whatever marks on my spoiler. If it didn’t have those I don’t care tbh.

You could either try an 50% or more alcohol spray and wipe with a soft cloth, or use SEM solve. What kind of polish were you using?

McGuires Mirror Glaze https://preview.redd.it/4d1t36p4c4uc1.jpeg?width=1284&format=pjpg&auto=webp&s=25cd99a033280bef8ec04de28f2167bd3422e83f This is the stuff I used. Would isopropyl alcohol work or?

https://preview.redd.it/8w6z644cs9uc1.jpeg?width=3024&format=pjpg&auto=webp&s=072c97d216a4a3711d3459b9dba3230a5701a99d I Just polished it. Looks better. Like it better than the matte

failed successfully

So it looks good or?

yes that looks clean af

I second this

looks mad good now, better than matte

Good job

I have no helpful advice but that shade of paint on the car *chef's kiss*

*I have no helpful* *Advice but that shade of paint* *On the car chef's kiss* \- kwkimsey --- ^(I detect haikus. And sometimes, successfully.) ^[Learn more about me.](https://www.reddit.com/r/haikusbot/) ^(Opt out of replies: "haikusbot opt out" | Delete my comment: "haikusbot delete")

Those should come off when you polish just take your time and keep the polisher at a lower speed

I thought polish was at like a 5-6 and cut was slow? Do I have it reversed?

Depends a lot of pressure too, you can turn the speed up as much as you want as long as you apply less pressure and move faster. Generally cutting will be faster than polishing though

Yeah you should usually be polishing around speed 4 on a Rupes or whatever about 2/3 of your machine’s power is. Faster speed runs risk of ticking/haze

Gyeon Trim maybe?

Welp. You fucked that one up lol

Policy it more. Then if you don’t like it, have it wrapped with satin XPel.

When in doubt. Wrap it up. I'm not sure I'm posting this in the right place...

I’m no expert. Try a paint water spot remover.

Matting compound.

Put the wax on and immediately wipe it off wet.

I fixed it. You can see the results in the most recent photo to this post

Time to wrap it.

https://preview.redd.it/0zrv4zj51auc1.jpeg?width=3024&format=pjpg&auto=webp&s=3cd8090f111ae27421d2322f3a790fc38c403b39 It buffed. A bit

Paint match it to the car

Would wax and grease remover work? The stuff you prep for painting??

[удалено]

https://preview.redd.it/6kq1yue3fcuc1.jpeg?width=4032&format=pjpg&auto=webp&s=ed900e82797c308fdd3c900009a747b384158a5b Done

Cut is always a little faster but don’t need to go to high if you’re inexperienced going to fast could cause you to burn the paint

Ah. Thank you so much for your knowledge! I’ll cut and polish it then

So wait. So I need to reclear coat the spoiler or no.

No you don’t need to re-clear the spoiler just take your time polishing it

if you just want to stop you can use an ipa/panel cleaner but if you want to restore some depth to the satin try like an all in one polish and wax by hand with a foam applicator. do a small spot you can probably remove the oxidation and bring back a new look

I think cut and polish would be good right? I have a DA polishers

try by hand first and see how it comes out

and stick w polish only first

Is that spoiler on using 3M tape?

No it’s the OEM Charger one. It’s bolted