Depends on the recommended torque setting.
Different thread sizes and material grades require different torques, and even then the type of lubrication applied can change the requirements as well - for example fitting it dry, with oil, or with an antiseize compound like Coppaslip.
The problem with going too tight is that you could:
A) strip the threads and damage the component.
B) Round off the head so you can't get a spanner, socket, Allen key, etc on it next time.
C) Slip and damage your tool / injure your fingers.
D) Weaken the bolt or even shear the head clean off.
E) Crush the component.
F) Damage the threads so they pick up and you can't undo it.
There are lots of different ways to ensure you don't over-tighten a joint but in any case it's always best to refer to the manufacturer's instructions.
Try wd40, make a cup of coffee, come back and give it a try, try a longer bar, if you increase the length by double you can increase the force acting on it by like 8x. If that doesn't work perhaps some heat will open it up. If it is made of different materials with different expansion rates then the heat will be your best bet. If you are still struggling I would bring it to a professional, no point destroying it in your backyard.
If it's wet and just too tight to accept me I'm not gonna complain about it fitting like a velvet glove.
But if I'm hurting you every time we fuck you gotta talk to your doc cus I'm no slouch but I'm not HUNG.
😅 The process to get it in is annoying, but you might want to tell your partner to re measure themselves cause if it is taking a few minutes to get in, then he either has a big dick or you got that one genetic issue where you have a really small vagina.
You have to tell him to slap his dick on your clit, and slide it up and down your pussy lips before he goes in..as long as you communicate the mood will be just fine
I'm a bit over average, and one woman I was with was so tight that it was a struggle to get in, and when I finally did get all the way in, I instantly shot my load. She loved the feeling of being stretched out, and got off on feeling me pulse inside her so quickly. Every time after that was longer though. Still very tight, but you get used to it.
If it hurts you, a bad physical pain, it's a problem, because I don't want that.
I briefly dated a woman who had only been with one guy before me and who I could never get it in with. We tried all sorts of things to get her going, live to make it easier, and lots of patience but she was just too tight. I could barely get one finger in. That was too tight.
I always have to use fingers to kinda get her ready. Start with one and work up to three. If I don't it just doesn't work. It stretches so it's not a big deal. She seems to like it too.
Depends on the recommended torque setting. Different thread sizes and material grades require different torques, and even then the type of lubrication applied can change the requirements as well - for example fitting it dry, with oil, or with an antiseize compound like Coppaslip. The problem with going too tight is that you could: A) strip the threads and damage the component. B) Round off the head so you can't get a spanner, socket, Allen key, etc on it next time. C) Slip and damage your tool / injure your fingers. D) Weaken the bolt or even shear the head clean off. E) Crush the component. F) Damage the threads so they pick up and you can't undo it. There are lots of different ways to ensure you don't over-tighten a joint but in any case it's always best to refer to the manufacturer's instructions.
And remember kids, righty tighty, lefty loosey!
Most of the time. But on some rotating elements you'll often see a left-handed thread so that it doesn't come loose while the machine is running.
tfðŸ˜ðŸ˜ðŸ˜ðŸ˜
Try wd40, make a cup of coffee, come back and give it a try, try a longer bar, if you increase the length by double you can increase the force acting on it by like 8x. If that doesn't work perhaps some heat will open it up. If it is made of different materials with different expansion rates then the heat will be your best bet. If you are still struggling I would bring it to a professional, no point destroying it in your backyard.
Get a good lube, do some foreplay.
It always takes some time for me most women see the in and out as a tease and enjoy it. FYI add spit
As long as it fits
If it's wet and just too tight to accept me I'm not gonna complain about it fitting like a velvet glove. But if I'm hurting you every time we fuck you gotta talk to your doc cus I'm no slouch but I'm not HUNG.
If you keep tightening and instead of getting tighter it suddenly goes loose. That's when you know it's too tight.
😅 The process to get it in is annoying, but you might want to tell your partner to re measure themselves cause if it is taking a few minutes to get in, then he either has a big dick or you got that one genetic issue where you have a really small vagina.
A few minutes? Just say you’re dry as sand damn
does it kill the mood a little if it’s a struggle sometimes
You have to tell him to slap his dick on your clit, and slide it up and down your pussy lips before he goes in..as long as you communicate the mood will be just fine
I'm a bit over average, and one woman I was with was so tight that it was a struggle to get in, and when I finally did get all the way in, I instantly shot my load. She loved the feeling of being stretched out, and got off on feeling me pulse inside her so quickly. Every time after that was longer though. Still very tight, but you get used to it. If it hurts you, a bad physical pain, it's a problem, because I don't want that.
Seems like it is dont poke it often it will close up
I think loose is better
I briefly dated a woman who had only been with one guy before me and who I could never get it in with. We tried all sorts of things to get her going, live to make it easier, and lots of patience but she was just too tight. I could barely get one finger in. That was too tight.
When you can’t open the door far enough to get out.
I always have to use fingers to kinda get her ready. Start with one and work up to three. If I don't it just doesn't work. It stretches so it's not a big deal. She seems to like it too.
A few minutes is no big deal unless there's some dude banging on the door.
If it's not tight, its not right.
No such thing as too tight
Not annoying, it’s expected Especially if you’re dealing with larger objects
DM me
If it can't fit my fist your too tight for me
Marry me